Shop
Showing 745–756 of 1301 results
Heat Shield (455 Exhaust Manifold)
Reproduction of the 1970 455 Driver Side Heat Shield.
Can use on newer 455 Engines but a small notch will need to be cut near the rear of the Heat Shield - See Photos below . . .
Fits - Buick 455
Photos below show the notch that may need to be cut in if used on new Exhaust Manifolds.
This notch is approximately 1" wide.
Close up of notch "cut out" towards the rear of the Heat Shield.
Close up of notch "cut out" towards the rear of the Heat Shield.
Heat Shield (Motor Mount)
Reproduction Heat Shield for the Passenger Side Motor Mount
Fits 400 - 430 - 455
Heat Shield (Starter)
Reproduction Heat Shield found on Buick Engines
Fits 350 - 400 - 430 - 455
Heat Stove – 350
This is an OEM Part
Fits 1970 – 1972 Skylark, GS & GSX with 350 Engine. (maybe other years as well)
These are NOT reproduced and somewhat hard to find.
It’s been cleaned, bead blasted and painted with High Temp Primer
.
.
This Part has Sold Out but we leave hard to find parts like this on the website so you can use the photo and information to help locate one!
.
OEM Parts are Original Equipment that came off a “Parts Car”.
Any of our OEM Parts will always be at least “Driver Quality”
Heat Stove – 455
This is an OEM Part
Fits 1970 – 1972 Skylark, GS & GSX with 455 Engine
These are NOT reproduced and somewhat hard to find in nice condition.
Very little Pitting on this one!
It's been cleaned, bead blasted and painted.
.
This Part has Sold Out but we leave hard to find parts like this on the website so you can use the photo and information to help locate one!
.
.
OEM Parts are Original Equipment that came off a “Parts Car”.
Any of our OEM Parts will always be at least “Driver Quality”
Heat Stove Mounting Bolts (Pair)
Heat Stove Mounting Bolts - Sold as a Pair (Requires 2)
Fits 1970 - 1972
Source - Stage 1 Restoration
Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models.
Don’t see what you need ? Give me a call, we probably have it!
Heat Stove Pipe (Black)
This is the Black Piping that goes from the heat stove to the bottom side of the Air Cleaner Assembly
Also called a "Pre Heat Tube"
Fits 1970 - 1972 (Maybe More)
Note: Our Heat Stove Pipe is the correct length. Be aware of other Vendors not providing a long enough piece!
Black was typically used on the GS, GSX & Skylark Models.
We know our parts fit because we use them in our Restoration Shop!
Installation Tip: The Heat Stove Pipe "Threads" onto the Air Cleaner Elbow. Install this end 1st then it simply slides onto the Heat Stove.
The picture below shows the "threads" that the heat stove utilizes . . . .
.
Installation Tip: The Heat Stove Pipe "Threads" onto the Air Cleaner Elbow. Install this end 1st then it simply slides onto the Heat Stove.
The picture below shows the "threads" that the heat stove utilizes . . . .
. 
Heater Blower Motor
Heater Blower Motor
Fits 1964 - 1972 Skylark, GS & GSX (Maybe more) .
Heater Blower Motor Fan
Heater Motor Blower Fan
Fits 1968 - 1972 Skylark, GS & GSXSPECIFICATIONS:
DIAMETER: 5.25 IN HUB OFFSET: 7/8 IN ROTATION: Clockwise SHAFT DIAMETER: 5/16 IN SHAFT HOLE INSIDE DIAMETER: .3125 IN WHEEL DIAMETER: 5-1/4 IN WHEEL WIDTH: 2-7/16 IN MATERIAL - Metal .
Heater Blower Motor Plug
2 Pc Blower Motor Plug
These are used on Cars without A/C
Heater Box Hardware Kit (Non A/C)
Heater Box Hardware Kit for Non A/C Car
Kit includes proper hardware for :
- Blower Motor Case to Firewall (2 Screws - 5 Nuts)
- Blower Motor to Blower Motor Case (5 Hex Screws)
- Blower Motor Wire Clip ( 1 )
Heater Box Seal Kit (A/C)
Heater Box Seal Kit for cars with A/C
Fits 1968 - 1972 Skylark, GS & GSX