Emblems
Showing 1–12 of 29 results
“350” Quarter Panel Emblem
"350" Quarter Panel Emblem
These are sold individually so if you need 2 please order "2"
BUA35
Note: Our Emblems are Made in the USA and Licensed by GM. Our competitors emblems, . . . probably not!
“455” Fender Emblem (Narrow Pin)
1970 – 72 “455” Fender Emblem (These are the ones typically found on our 1970 - 1972 Buicks)
These are sold individually so if you need 2 please order “2”
BUA12
Note: Our Emblems are Made in the USA and Licensed by GM.
Our competitors emblems, . . . probably not!
Note: Buick used 2) different 455 Emblems throughout the years.
This one measures roughly 1 3/8″ from stud to stud.
If you’re planning to use existing holes please compare measurements before ordering!
“455” Fender Emblem (NOS)
NOS 455 Fender Emblem
GM Part Number 1243119 (Later superseded to 1394199)
Brand New in the GM Box (Just have 1 of these)
Note: GM Produced 2 different versions of these 455 Fender Emblems
This one measures 1 7/8" from stud to stud. Be sure to measure your mounting holes (unless you're drilling new ones)
.
“455” Fender Emblem (Wide Pin)
1970 - 74 "455" Fender Emblem
These are sold individually so if you need 2 please order "2"
Note: Buick used 2) different 455 Emblems throughout the years.
This one measures roughly 1 7/8" from stud to stud.
If you're planning to use existing holes please compare measurements before ordering!
“Buick Motor Division” Fender Emblem
1970 - 72 "Buick Motor Division" Fender Emblem - Typically found on the 350 equipped GS's.
These are sold individually so if you need 2 please order "2"
BUA23
Note: Our Emblems are Made in the USA and Licensed by GM.
Our competitors emblems, . . . probably not!
“BUICK” Rear Bumper Emblem – 1970
Reproduction "BUICK" Rear Bumper Emblem - 1970
Note: We've installed enough of these that we feel the mold for these doesn't allow the Emblem to fit 100% flat on the Bumper as it should. With that being said if you go through with the purchase of this item be aware that you will have to "Draw in the Ends" as its being tightened. This is a pretty minor issue but we like to let our customers know up front so there are no surprises. If this is something you don't want to deal with you'll have to use an original GM emblem. Once installed they look great.
“BUICK” Trunk Lid Emblem
"BUICK" Trunk Lid Emblem
These are typically found on the 1971 Models
BUA54A
Note: Our Emblems are Made in the USA and Licensed by GM. Our competitors emblems, . . . probably not!
.
“By Buick” Trunk Lid Emblem
"BY BUICK" Trunk Lid Emblem
These are typically found on the 1971 Models
BUA53
Note: Our Emblems are Made in the USA and Licensed by GM.
Our competitors emblems, . . . probably not!
“Custom” Quarter Panel Emblem (1970 – 72)
"Custom" Quarter Panel Emblem 1970 - 1972
These are sold individually so if you need 2 please order "2"
BUA42
Note: Our Emblems are Made in the USA and Licensed by GM. Our competitors emblems, . . . probably not!
.
“GS” Trunk Lid Emblem
1970 - 72 "GS" Trunk Emblem
BUA54
Please Note: These look similar to the Fender Emblems but have different mounting stud locations!
Note: Our Emblems are Made in the USA and Licensed by GM. Our competitors emblems, . . . probably not!