Interior – Dash

Showing 49–60 of 102 results

Glove Box Liner (For A/C Cars)
Replacement Glove Box Liner for cars WITH A/C Made in the USA! Fits 1970 - 1972     Be sure to check out our Glove Box Hardware Kit .
$29.00 Add to cart
Glove Box Liner (Non A/C)
Replacement Glove Box Liner for cars WITHOUT A/C Made in the USA! Fits 1970 - 1972     Be sure to check out our Glove Box Hardware Kit
$29.00 Add to cart
Glove Box Liner & Door Hardware
Glove Box Liner & Door Hardware Kit Kit Includes:
  • 3) Glove Box Door Screws (There are 5 spots but Buick only utilized 3)
  • 6) Glove Box Liner Screws
  • 5) Glove Box Door & Liner Spring Nuts
  Fits - 1970 - 1972 Skylark, GS & GSX   Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models. Don’t see what you need ?  Give me a call, we probably have it!  
$10.00 Add to cart
Glove Box Rubber Bumper Kit
Glove Box Door Bumper Kit Kit Includes:
  • 2) Glove Box Door Rubber Bumpers
  • 1) Glove Box Check Grommet
  • 1) Glove Box Link Grommet
  Fits – 1970 – 1972 Skylark, GS & GSX   Note; We've only found a couple of these items from ONE Manufacture and unfortunately there parts are very expensive. Overpriced in our opinion but if you need these parts they're the only ones reproducing them. So in short I apologize the high price tag on this time but you won't find them anywhere else . . . .   Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models. Don’t see what you need ?  Give me a call, we probably have it!  
$32.00 Add to cart
GSX Dash Emblem
GSX Dash Pad Emblem This is a very nice and accurate reproduction of the GSX Dash Pad Emblem Fits 1970 - 1972        
$159.00 Add to cart
Headlight Switch Ground Spade
This is an OEM Part  Headlight Switch Ground Spade These are NOT currently reproduced. Fits 1970 - 1972 Headlight Switches   Note: Because Buick used a Plastic Dash Bezel it is required to Ground the Headlight Switch!   Photo below shows the Factory Grounds for the Headlight Switch and the Wiper Switch. These should be in use for each switch to work properly.   Each one shown here installed correctly   OEM Parts are Original Equipment that came off a “Parts Car”. Any of our OEM Parts will always be at least “Driver Quality”      
$10.00 Add to cart
Headlight Switch Pull Knob
Replacement Headlight Switch Pull Knob Fits 1970- 1972     Helpful Hint: For easier installation we recommend grinding more of a "Pointed Tip" at the end of the shaft. It helps make installation a bit easier!    
$19.00 Add to cart
Horn Cap Emblem
Buick Horn Cap Emblem for the 3 Spoke Rallye Steering Wheel Fits 1970 - 1972 Buick Horn Caps (Does Fit other years as well) This is a nice reproduction!   Note: Be sure to line up the notch at the bottom of the emblem with the tab in the Horn Cap Housing. This will "clock" the emblem properly which is important for proper alignment of the Cap to the Retainer it snaps in to. The Red Circles need to match once the Cap is Snapped into place. This will allow the Horn Cap to fit properly and function  properly!        
$39.00 Add to cart
Sale!
Horn Cap For Rallye Wheels
Replacement Horn Cap in Black for the Rallye Steering Wheels Fits 1969 - 1972     Note: The manufacture of these does not install the "Buick" Emblem so when you go to install it be sure to line up the notch at the bottom of the emblem with the tab in the Horn Cap Housing. This will "clock" the emblem properly which is important for proper alignment of the Cap to the Retainer it snaps in to. The Red Circles need to match once the Cap is Snapped into place. This will allow the Horn Cap to fit properly and function  properly!   The photo below shows the back side of the Horn Cap (Left Side of Photo) and where the 3 cutouts should be to snap into the retainer properly. If you have any questions on this feel free to call me!    
$65.00 Add to cart
Horn Cap Mounting Kit (Non Tilt)
This is a replacement Horn Contact & Horn Cap Mounting Kit for anyone using the 3 Spoke Rallye Steering Wheels (Non Tilt) Kit Includes:
  • Cancel Cam
  • 6) Steering Wheel to Hub Screws
  • 3) Horn Cap Retainer to Hub Screws
  • Horn Cap Retainer (Contact)
  • Horn "Contact Pin"
  • Horn "Spring"
  • Horn Spring Retainer (Insulator)
    Note:  The Aluminum "Contact Pin" is a tad long on purpose.  Trim to proper length for your application. Generally 3/4" is just about right.   Note: For a Bigger Photo of this click here     For a bigger picture of this Diagram please see Picture # 32 on our Factory Diagrams Page            
$34.00 Add to cart
Horn Cap Mounting Kit (Tilt)
This is a replacement Horn Contact & Horn Cap Mounting Kit for anyone using the 3 Spoke Rallye Steering Wheels (For Tilt Columns) Kit Includes:
  • Cancel Cam
  • 6) Steering Wheel to Hub Screws
  • 3) Horn Cap Retainer to Hub Screws
  • Horn Cap Retainer (Contact)
  • Horn “Contact Pin”
  • Horn “Spring”
  • Horn Spring Retainer (Insulator)
    Note:  The Aluminum "Contact Spring" is a tad long on purpose.  Trim to proper length for your application. Generally 3/4″ is just about right.   Note: For a Bigger Photo of this click here     For a bigger picture of this Diagram please see Picture # 32 on our Factory Diagrams Page  
$33.00 Add to cart
Horn Cap Mounting Schematic
Here is the Factory Horn Cap Mounting Schematic for Buick's 3 Spoke Steering Wheel . . . .     For a bigger picture of this Diagram please see Picture # 32 on our Factory Diagrams Page
$0.00 Read more