Engine Bay Parts
Showing 49–60 of 108 results
View cart “Ground Strap w/Mounting Hardware” has been added to your cart.
Grommet (Speedometer Cable Grommet)
Correct Speedometer Cable Grommet
Fits 1970 - 1972 GM A Body
.
Ground Strap
This is the Factory Correct Ground Strap found on our Buick's.
5/16" eyelet on one side for firewall mounting.
3/8" eyelet on other end for cylinder head mounting.
We also sell this with the correct mounting Hardware if needed. Search "Ground Strap" to locate.
Note: We use & sell Lectric Limited Products because they're Made in the USA using Factory GM Blue Prints!
.
Ground Strap w/Mounting Hardware
This is the Factory Correct Ground Strap w/ Mounting Hardware found on our Buick’s.
5/16″ eyelet on one side for firewall mounting.
3/8″ eyelet on other end for cylinder head mounting.
Note: We use & sell Lectric Limited Products because they’re Made in the USA using Factory GM Blue Prints!
.
Sale!
$249.95 $149.95
Add to cart
GS Hood Seal Plates – 1972 (Discounted)!
I have a few sets of 1972 GS/GSX Hood Seal Plates that have some slight scuff marks on them and therefore they’re discounted! This is pretty minor and they may not show up in the photos. The finish appears to be a tad shinier on one side as well but only one side shows once they’re mounted.
These are New Reproductions and normally Retail for $249.00
These are reduced to $149.95 Per Set! (Plus actual shipping to your door)
Only a handful of these available at this price!
.
Heater Box Hardware Kit (Non A/C)
Heater Box Hardware Kit for Non A/C Car
Kit includes proper hardware for :
- Blower Motor Case to Firewall (2 Screws - 5 Nuts)
- Blower Motor to Blower Motor Case (5 Hex Screws)
- Blower Motor Wire Clip ( 1 )
Hood Adjustment Bumper (Front)
These are the correct Hood Adjustment Bumpers used on the Front
$4.00 Each - 3 Required per car.
Fits 1970 - 1972
Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models.
Don’t see what you need ? Give me a call, we probably have it!
Hood Adjustment Bumper (Rear)
These are the correct Hood Adjustment Bumpers for the Rear
$15.00 Each – 2 Required
Fits 1970 – 1972
Note: To be "Concours Correct" you would want to send these off to be Gold Cad.
Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models.
Don’t see what you need ? Give me a call, we probably have it!
.
Hood Adjustment Bumper Kit
10 Pc Hood Adjustment/Bumper Kit
Kit Includes the following:
- 3) Front Adjustment Bumpers
- 3) Front Adjustment Retainer Nuts
- 2) Rear Adjustment Bumpers
- 2) Rear Adjustment Nuts
- These are the CORRECT from Bumpers!!
Hood Adjustment Bumper Kit (Front)
6 Pc Hood Adjustment Bumper Kit
These are the Correct Hood Adjustment Bumpers and Nut Retainers found on our Buick's
Fits 1970 - 1972 (Front of Hood)
Kit includes:
- 3) Front Adjustment Bumpers
- 3) Retainer Nuts
Hood Adjustment Retainer Nuts
Front Hood Bumper Retainer Nuts - 3 Pack
These are the correct retainer nuts found in the core support to house the Hood Bumpers
Fits 1970 - 1972 (Each car uses 3 of these)
Nice Reproduction Made in the USA!
Helpful Hint: Once you have these adjusted they're meant to be locked down. You can use a 3/4" Open Ended wrench to twist the top half to the "Lock Position" (Clockwise)
Note: I have the Correct Hood Bumpers also. Click the Link for details.
Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models.
Don’t see what you need ? Give me a call, we probably have it!
Hood Insulation (Yellow)
The correct "Yellow" Hood Insulation
5 Piece Kit - Pre Cut
Fits 1968 - 1972 Skylark or GS/GSX
Note: GS & GSX Models only use 3 of the 5 Pcs!
Photo below shows the Kit you'll receive:
Hood Latch Assembly – Replated
Beautifully Re-Plated Hood Latch assembly for Consours Restorations
Fits 1970 - 1972 Skylark, GS & GSX
Source - OE (Original Equipment)
OEM Parts are Original Equipment that came off a “Parts Car”.
Any of our OEM Parts will always be at least “Driver Quality”