Engine Bay Parts
Showing 49–60 of 102 results
Heater Box Hardware Kit (Non A/C)
Heater Box Hardware Kit for Non A/C Car
Kit includes proper hardware for :
- Blower Motor Case to Firewall (2 Screws - 5 Nuts)
- Blower Motor to Blower Motor Case (5 Hex Screws)
- Blower Motor Wire Clip ( 1 )
Hood Adjustment Bumper (Front)
These are the correct Hood Adjustment Bumpers used on the Front
$4.00 Each - 3 Required per car.
Fits 1970 - 1972
Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models.
Don’t see what you need ? Give me a call, we probably have it!
Hood Adjustment Bumper (Rear)
Hood Adjustment Bumpers for the Rear
$16.00 Each – 2 Required - If you need 2 be sure to order two! Fits 1970 – 1972 Skylark, GS & GSX Note: To be "Concours Correct" you would want to send these off to be Gold Cad.
Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models.
Don’t see what you need ? Give me a call, we probably have it!
. 
Hood Adjustment Bumper Kit
10 Pc Hood Adjustment/Bumper Kit
Kit Includes the following:
Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models.
Don’t see what you need ? Give me a call, we probably have it!
Key words . . . Hood Bumpers, Hood Adjusters
.
- 3) Front Adjustment Bumpers
- 3) Front Adjustment Retainer Nuts
- 2) Rear Adjustment Bumpers
- 2) Rear Adjustment Nuts
- These are the CORRECT from Bumpers!!
Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models.
Don’t see what you need ? Give me a call, we probably have it!
Key words . . . Hood Bumpers, Hood Adjusters
. 
Hood Adjustment Bumper Kit (Front)
6 Pc Hood Adjustment Bumper Kit
These are the Correct Hood Adjustment Bumpers and Nut Retainers found on our Buick's
Fits 1970 - 1972 (Front of Hood)
Kit includes:
Note: Once you have your hood height set you can use a 3/4" wrench to tighten (clockwise) the Adjuster as shown in the photo!
Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models.
Don’t see what you need ? Give me a call, we probably have it!
Key Words . . . Hood Bumpers, Hood Adjusters
- 3) Front Adjustment Bumpers
- 3) Retainer Nuts
Note: Once you have your hood height set you can use a 3/4" wrench to tighten (clockwise) the Adjuster as shown in the photo!
Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models.
Don’t see what you need ? Give me a call, we probably have it!
Key Words . . . Hood Bumpers, Hood Adjusters 
Hood Adjustment Retainer Nuts
Front Hood Bumper Retainer Nuts - 3 Pack
These are the correct retainer nuts found in the core support to house the Hood Bumpers
Fits 1970 - 1972 (Each car uses 3 of these)
Nice Reproduction Made in the USA!
Helpful Hint: Once you have these adjusted they're meant to be locked down. You can use a 3/4" Open Ended wrench to twist the top half to the "Lock Position" (Clockwise)
Note: I have the Correct Hood Bumpers also. Click the Link for details.
Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models.
Don’t see what you need ? Give me a call, we probably have it!
Helpful Hint: Once you have these adjusted they're meant to be locked down. You can use a 3/4" Open Ended wrench to twist the top half to the "Lock Position" (Clockwise)
Note: I have the Correct Hood Bumpers also. Click the Link for details.
Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models.
Don’t see what you need ? Give me a call, we probably have it!
Hood Insulation (GS & GSX)
GS & GSX Under Hood Insulation
3 Piece Kit - Pre Cut Fits 1968 - 1972 GS & GSX Note: Skylark Models use 5 Pcs so if you have a Skylark hood you'll want this kit > Skylark Hood Insulation This item was not being made correctly for our Buick's so we have a new vendor that IS making it correct. If you purchase this elsewhere you're probably not getting the correct stuff!- Correct Shape
- Correct Color
- Correct Center Hole (Buick exclusive)
Install Tip: In most cases you can get a little better fit if you trim the sides a bit. Not to much, just sneak up on it and you'll find it will fit the hood even better. Also, install with care as this stuff is FRAGILE!
[gallery ids="12428,12429"] .
Hood Insulation (Skylark)
Skylark Under Hood Insulation
5 Piece Kit - Pre Cut Fits 1968 - 1972 Skylark Note: GS & GSX Models only use 3 of the 5 Pcs so if you have a GS hood you'll want this kit > GS Hood Insulation This item was not being made correctly for our Buick's so we have a new vendor that IS making it correct. If you purchase this elsewhere you're probably not getting the correct stuff!- Correct Shape
- Correct Color
- Correct Center Hole (Buick exclusive)
Install Tip: In most cases you can get a little better fit if you trim the sides a bit. Not to much, just sneak up on it and you'll find it will fit the hood even better. Also, install with care as this stuff is FRAGILE!
.
Hood Latch Assembly – Replated
Beautifully Re-Plated Hood Latch assembly for Consours Restorations
Fits 1970 - 1972 Skylark, GS & GSX
.
This Part has Sold Out but we leave hard to find parts like this on the website so you can use the photo and information to help locate one!
.
.
OEM Parts are Original Equipment that came off a “Parts Car”.
Any of our OEM Parts will always be at least “Driver Quality”
.
OEM Parts are Original Equipment that came off a “Parts Car”.
Any of our OEM Parts will always be at least “Driver Quality”
. 
Hood Release Handle
Reproduction Hood Release Handle
Fits 1970 - 1972 Skylark GS & GSX Note: Retaining Clip also available if needed .
Hood Tach Harness Clip
Hood Tach Wire Harness Clip
Clip used to attach the Hood Tach Harness to the Hood
.
. 
Horn Mounting Bolts
Horn Mounting Kit
Kit Includes:- 2) Zinc Plated Bolts with Built in Star Washers
- 2) Square Nuts to weld on Back Side of Horn Brackets
- Enough to do BOTH Horns!
We weld the Nuts on the back side of the horns as shown in the photo. That allows us to use a Standard thread Zinc Bolt with built in Star Washer. When done and mounted it looks like the factory bolts and provides a better ground!
