Shop

Floor Shift Handle (Woodgrain)

Nice reproduction of the woodgrain shift handle used on Floor Shifters Fits 1970 - 72 (Correct for 1970) - Woodgrain Version If you need the Correct Hardware for your Floor Shifter be sure to check out our Floor Shift Hardware Kit Note: When installing the screws that hold the handle in place be sure to place some lube on them and install slowly!! (Otherwise you can crack the plastic handle)

$39.00 Add to cart

Floor Shift Handle Cradle

This is the (Shifter Cradle) for the Automatic Floor Shift assembly used by Buick Fits 1970 - 1972 Skylark, GS & GSX Shifters 4 pcs total It is crucial that you use the Proper Phillips Screws when installing the Handle and Pull bar or the shifter will not slide up and down properly! If you need the Correct Hardware for your Floor Shifter be sure to check out our Floor Shift Hardware Kit

Note: If you're also using the aftermarket Chrome Shifter Handle Insert you will want to drill out the holes shown below to 5/16". We've found that the Chrome Shifter Handle Inserts are a tad to short to properly snap into the shifter cradle. See photos below for more on this! The Circled area shows the hole that needs to be "enlarged". In most cases you can simply drill this hole out to 5/16". (It's normally a 1/4" hole) The bigger hole allows for the Tabs on the Chrome Insert to lock in place. IF you still have a Factory Handle Insert then you may not need to do this.

If needed you can also take a hand file or dremel tool and enlarge the hole towards the TOP! This will allow the Chrome Insert to Snap in to place easier.

You're basically enlarging the holes so that the Shifter Insert Tabs will snap in to the Cradle better.

$59.00 Add to cart

Floor Shift Handle Insert (Aluminum Version)

Reproduction of the Chrome Insert that's inserted into the Shift Handle. This is the Polished Aluminum Version made by Michael Garrison Fits 1970 - 72 Source - HTR

$45.00 Add to cart

Floor Shift Handle Insert (Plastic Version)

Reproduction of the Chrome Insert that's inserted into the Shift Handle. This is the Plastic Version Fits 1970 - 72 Skylark, GS & GSX Note: Unfortunately these do not fit perfectly without a little "Fine Tuning". We've found that most of these are a tad to short to properly snap into the shifter cradle. So if you purchase this item be aware that some fine tuning may be required to fit perfectly. If you don't want to go through this process I recommend trying to find a nice original piece. Otherwise if you simply open up the holes that the Tabs at the bottom fit into it will work much better. See photos below for more on this! The Circled area shows the hole that needs to be "enlarged". In most cases you can simply drill this hole out to 5/16". (It's normally a 1/4" hole) The bigger hole allows for the Tabs on the Chrome Insert to lock in place.

If needed you can also take a hand file or dremel tool and enlarge the hole towards the TOP! This will allow the Chrome Insert to Snap in to place easier.

You're basically enlarging the holes so that the Shifter Insert Tabs will snap in to the Cradle better.

If you need the Correct Hardware for your Floor Shifter be sure to check out our Floor Shift Hardware Kit

$29.00 Add to cart

Floor Shift Handle Pull Bar

This is commonly referred to as the "Pull Bar" for an automatic Floor Shift Fits 1970 - 72

It is crucial that you use the Proper Phillips Screws when installing the Handle and Pull bar or the shifter will not slide up and down properly! If you need the Correct Hardware for your Floor Shifter be sure to check out our Floor Shift Hardware Kit Also, when installing the screws that hold the handle & the pull bar in place be sure to place some lube on them and install slowly!! (Otherwise you can crack the plastic)

$19.00 Add to cart

Floor Shift Handle Release Springs

These are the springs that are inside the Floor Shift Handle and help release the Pull Bar Fits 1970 - 72 Sold as a Pair If you need the Correct Hardware for your Floor Shifter be sure to check out our Floor Shift Hardware Kit

$5.00 Add to cart

Floor Shift Pivot Bushings

1968 - 1977 Buick Floor Shift Pivot Bushings These are only available here! Made in the USA Sold as a Pair for $18 Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models. Don’t see what you need ? Give me a call, we probably have it!