Shop
Showing 1285–1296 of 1301 results
Wiper Switch Ground Tab – OE
Windshield Wiper Switch Ground Spade
This is an OEM Part These are NOT reproduced. Fits 1970 – 1972 Skylark, GS & GSX Wiper Switches These have now sold out but I'm leaving them on here so our customers can see what is needed in case they're missing it. Note: Because Buick used a Plastic Dash Bezel it is required to Ground the Headlight Switch & the Windshield Switch! Photo below shows the Factory Grounds for the Headlight Switch and the Wiper Switch. These should be in use for each switch to work properly.
Each one shown here installed correctly
This Part has Sold Out but we leave hard to find parts like this on the website so you can use the photo and information to help locate one!
.
OEM Parts are Original Equipment that came off a “Parts Car”.
Any of our OEM Parts will always be at least “Driver Quality”
Wiper Transmission Mounting Hardware
Buick Wiper Transmission Mounting Hardware
Fits 1964 - 1972
Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models.
Don’t see what you need ? Give me a call, we probably have it!
Wire Clip (Firewall)
This clip is generally used to hold the Blower Motor Wire near the Heater Core Cover
Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models.
Don’t see what you need ? Give me a call, we probably have it!
Wire Harness “J” Clip
This is the Clip Buick used to hold the Engine Wire Harness to the Firewall.
I've seen some cars with just 1 clip and other cars with 2 clips.
Fits 1970 - 1972
$3.00 Each
Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models.
Don’t see what you need ? Give me a call, we probably have it!
Wire Harness Fastener – 3″ Version
This is the 3" Factory Wire Harness strap used on the Core Support for the Headlight Harness as well as the Fuel Tank Sending Unit wire.
These are probably used in other areas as well but these are the main locations on 1970 - 1972 Models
$2.00 Each
Fits 1970 - 1972 Skylark, GS & GSX
Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models.
Don’t see what you need ? Give me a call, we probably have it!
Wire Harness Fastener – 4″ Version
This is the 4" Factory Wire Harness strap used on the Inner Fender for the Headlight Harness as well as the Washer Pump Hose
These are probably used in other areas as well but these are the main locations on 1970 - 1972 Models
$2.00 Each
Fits 1970 - 1972 Skylark, GS & GSX
Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models.
Don’t see what you need ? Give me a call, we probably have it!
Wire Harness Shield (1970)
This is an OEM Part
Wire Harness Shield
Cleaned, Bead Blasted and Painted
This version is typically found on the 1970 Engines and somewhat hard to find.
OEM Parts are Original Equipment that came off a “Parts Car”.
Any of our OEM Parts will always be at least “Driver Quality”
Wire Harness Shield (1971/72)
This is an OEM Part
Wire Harness Shield - Also holds your PCV Hose
Cleaned, Bead Blasted and Painted
This version is typically found on the 1971 & 72 Engines
OEM Parts are Original Equipment that came off a “Parts Car”.
Any of our OEM Parts will always be at least “Driver Quality”
Sale!
Original price was: $21.00.$20.00Current price is: $20.00.
Add to cart
Wire Harness Tape
1" Wide Non Adhesive Harness Tape
Source - Lectric Limited
Note: We use & sell Lectric Limited Products because they’re Made in the USA using Factory GM Blue Prints!
Wiring Diagram – 1970, 71, 72
We've replicated the GM Chassis Manual Wiring Diagram into a Poster Size Diagram so it's easy to read.
These measure 24" x 36" and are color coded just like the originals. These are nice quality and easy to read!
Again, these are from the Factory Wiring Diagram, not some bootleg diagram that's been reprinted 1,000's of times.
If you have a wiring issue or just want to know what wires do what this is a great tool to have!
Note: 1970 - 1972 were the same exact diagram other than a seat belt warning light added in 1972.
So with that being said anyone ordering a 1970, 71 or 72 will simply receive the "72" diagram.
Photo Below Shows the 1970 Diagram just for reference . . .
Close up Photo Below shows the clarity and detail . . . .
Close up Photo Below shows the clarity and detail . . . .
Z Bar Bushing for 455 Cars
This is the Correct bushing used in the Clutch Fork Assembly as well as the Z-Bar.
Fits 1970 – 1972 GS & GS (and maybe some earlier 4 speed models)
Note: In some cases we've had to file the Inside Collar down just a tad to get a perfect fit.
.
Z-Bar – 350 Equipped Cars
Reproduction Z-Bar for the 350 Equipped Cars
Fits 1968 - 1972
.