Shop
Showing 1285–1296 of 1303 results
View cart “Wiring Diagram – 1970, 71, 72” has been added to your cart.

Wiper Motor Transmission Arm (OE)
Factory GM Wiper Motor Arm
Factory Original GM Piece - Includes Factory Mounting Nut
Correct for 1970 - 1972 Buick GS, GSX & Skylark
OEM Parts are Original Equipment that came off a “Parts Car”.
Any of our OEM Parts will always be at least “Driver Quality”
.


Wiper Motor Transmission Clip
This is the Clip that holds the wiper transmission to the wiper motor bracket
Fits 1964 - 1972
Note: Wiper Motor Arm NOT included. For photo purposes only. (Sold Separately)
Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models.
Don’t see what you need ? Give me a call, we probably have it!


Wiper Switch Ground Tab – OE
Windshield Wiper Switch Ground Spade
This is an OEM Part These are NOT reproduced. Fits 1970 – 1972 Skylark, GS & GSX Wiper Switches These have now sold out but I'm leaving them on here so our customers can see what is needed in case they're missing it. Note: Because Buick used a Plastic Dash Bezel it is required to Ground the Headlight Switch & the Windshield Switch! Photo below shows the Factory Grounds for the Headlight Switch and the Wiper Switch. These should be in use for each switch to work properly.



Wiper Transmission Mounting Hardware
Buick Wiper Transmission Mounting Hardware
Fits 1964 - 1972
Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models.
Don’t see what you need ? Give me a call, we probably have it!

Wire Clip (Firewall)
This clip is generally used to hold the Blower Motor Wire near the Heater Core Cover
Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models.
Don’t see what you need ? Give me a call, we probably have it!

Wire Harness “J” Clip
This is the Clip Buick used to hold the Engine Wire Harness to the Firewall.
I've seen some cars with just 1 clip and other cars with 2 clips.
Fits 1970 - 1972
$3.00 Each
Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models.
Don’t see what you need ? Give me a call, we probably have it!

Wire Harness Fastener – 3″ Version
This is the 3" Factory Wire Harness strap used on the Core Support for the Headlight Harness as well as the Fuel Tank Sending Unit wire.
These are probably used in other areas as well but these are the main locations on 1970 - 1972 Models
$2.00 Each
Fits 1970 - 1972 Skylark, GS & GSX
Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models.
Don’t see what you need ? Give me a call, we probably have it!

Wire Harness Fastener – 4″ Version
This is the 4" Factory Wire Harness strap used on the Inner Fender for the Headlight Harness as well as the Washer Pump Hose
These are probably used in other areas as well but these are the main locations on 1970 - 1972 Models
$2.00 Each
Fits 1970 - 1972 Skylark, GS & GSX
Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models.
Don’t see what you need ? Give me a call, we probably have it!

Wire Harness Shield (1970)
This is an OEM Part
Wire Harness Shield
Cleaned, Bead Blasted and Painted
This version is typically found on the 1970 Engines and somewhat hard to find.
OEM Parts are Original Equipment that came off a “Parts Car”.
Any of our OEM Parts will always be at least “Driver Quality”


Wire Harness Shield (1971/72)
This is an OEM Part
Wire Harness Shield - Also holds your PCV Hose
Cleaned, Bead Blasted and Painted
This version is typically found on the 1971 & 72 Engines
OEM Parts are Original Equipment that came off a “Parts Car”.
Any of our OEM Parts will always be at least “Driver Quality”

Sale!
$21.00 $20.00
Add to cart

Wire Harness Tape
1" Wide Non Adhesive Harness Tape
Source - Lectric Limited
Note: We use & sell Lectric Limited Products because they’re Made in the USA using Factory GM Blue Prints!

Wiring Diagram – 1970, 71, 72
We've replicated the GM Chassis Manual Wiring Diagram into a Poster Size Diagram so it's easy to read.
These measure 24" x 36" and are color coded just like the originals. These are nice quality and easy to read!
Again, these are from the Factory Wiring Diagram, not some bootleg diagram that's been reprinted 1,000's of times.
If you have a wiring issue or just want to know what wires do what this is a great tool to have!
Note: 1970 - 1972 were the same exact diagram other than a seat belt warning light added in 1972.
So with that being said anyone ordering a 1970, 71 or 72 will simply receive the "72" diagram.
Photo Below Shows the 1970 Diagram just for reference . . .
Close up Photo Below shows the clarity and detail . . . .

