Shifter Parts (Automatic)
Showing 13–24 of 29 results
Floor Shift Console Top “Door Insert”
This is the Chrome Insert that is mounted to the Floor Shift Console Door (Door Lid itself not included)
Fits 1970 - 1977 Buick Consoles
This can be used in conjunction with our Replacement Lid Item # 1232871
Cover Shown below with Lid & Woodgrain Kit installed (Both Sold Separately)
Cover Shown below with Lid & Woodgrain Kit installed (Both Sold Separately)
Floor Shift Console Top Insert “Buick”
"Buick" nameplate (emblem) that mounts inside the Floor Shift Console
This is a nice reproduction!
Fits 1970 - 1972
If you need the Correct Hardware for your Floor Shifter be sure to check out our Floor Shift Hardware Kit
.
Floor Shift Console Wood Grain Decal Kit
Wood Grain Decal Kit for the Automatic Floor Shift Console.
Fits 1970 - 1972 Buick Consoles
(Lower priced alternative to our Concours Level Decal Set)
If you need the Correct Hardware for your Floor Shifter be sure to check out our Floor Shift Hardware Kit
.
Floor Shift Console Wood Grain Decal Kit – Mark Wajda Version
Wood Grain Decal Kit for the Automatic Floor Shift Console.
These are produced by Mark Wajda - same manufacture of the Quality Dash Decal Sets we carry.
Fits 1970 – 1972
If you need the Correct Hardware for your Floor Shifter be sure to check out our Floor Shift Hardware Kit
Note: Console NOT included!
Floor Shift Detent Plate
Detent Plate for Floor Shifter
Fits 1970 - 1972 (Maybe 168/69)?
Floor Shift Gear Selector
Gear Shift Selector used on Automatic Floor Shifters
Fits 1970 - 1972
If you need the Correct Hardware for your Floor Shifter be sure to check out our Floor Shift Hardware Kit
Floor Shift Handle (Black)
Nice reproduction of the black shift handle used on Floor Shifters
Fits 1970 - 72 (Correct for 1971 & 72)
If you need the Correct Hardware for your Floor Shifter be sure to check out our Floor Shift Hardware Kit
Note: When installing the screws that hold the handle in place be sure to place some lube on them and install slowly!! (Otherwise you can crack the plastic handle)
Floor Shift Handle (Woodgrain)
Nice reproduction of the woodgrain shift handle used on Floor Shifters
Fits 1970 - 72 (Correct for 1970) - Woodgrain Version
If you need the Correct Hardware for your Floor Shifter be sure to check out our Floor Shift Hardware Kit
Note: When installing the screws that hold the handle in place be sure to place some lube on them and install slowly!! (Otherwise you can crack the plastic handle)
Floor Shift Handle Cradle
This is the (Shifter Cradle) for the Automatic Floor Shift assembly used by Buick
Fits 1970 - 1972
4 pcs total
It is crucial that you use the Proper Phillips Screws when installing the Handle and Pull bar or the shifter will not slide up and down properly!
If you need the Correct Hardware for your Floor Shifter be sure to check out our Floor Shift Hardware Kit
Note: If you're also using the aftermarket Chrome Shifter Handle Insert you will want to drill out the holes shown below to 5/16". We've found that the Chrome Shifter Handle Inserts are a tad to short to properly snap into the shifter cradle. See photos below for more on this!
The Circled area shows the hole that needs to be "enlarged". In most cases you can simply drill this hole out to 5/16". (It's currently a 1/4" hole) The bigger hole allows for the Tabs on the Chrome Insert to lock in place. IF you still have a Factory Handle Insert then you may not need to do this.
If needed you can also take a hand file or dremel tool and enlarge the hole towards the TOP!
This will allow the Chrome Insert to Snap in to place easier.
You're basically enlarging the holes so that the Shifter Insert Tabs will snap in to the Cradle better.
Note: If you're also using the aftermarket Chrome Shifter Handle Insert you will want to drill out the holes shown below to 5/16". We've found that the Chrome Shifter Handle Inserts are a tad to short to properly snap into the shifter cradle. See photos below for more on this!
The Circled area shows the hole that needs to be "enlarged". In most cases you can simply drill this hole out to 5/16". (It's currently a 1/4" hole) The bigger hole allows for the Tabs on the Chrome Insert to lock in place. IF you still have a Factory Handle Insert then you may not need to do this.
If needed you can also take a hand file or dremel tool and enlarge the hole towards the TOP!
This will allow the Chrome Insert to Snap in to place easier.
You're basically enlarging the holes so that the Shifter Insert Tabs will snap in to the Cradle better.
Floor Shift Handle Insert (Aluminum Version)
Reproduction of the Chrome Insert that's inserted into the Shift Handle.
This is the Polished Aluminum Version made by Michael Garrison
Fits 1970 - 72
Source - HTR
Floor Shift Handle Insert (Plastic Version)
Reproduction of the Chrome Insert that's inserted into the Shift Handle.
This is the Plastic Version
Fits 1970 - 72
Note: Unfortunately these do not fit perfectly without a little "Fine Tuning". We've found that most of these are a tad to short to properly snap into the shifter cradle. So if you purchase this item be aware that some fine tuning may be required to fit perfectly. If you don't want to go through this process I recommend trying to find a nice original piece. Otherwise if you simply open up the holes that the Tabs at the bottom fit into it will work much better. See photos below for more on this!
The Circled area shows the hole that needs to be "enlarged". In most cases you can simply drill this hole out to 5/16". (It's currently a 1/4" hole) The bigger hole allows for the Tabs on the Chrome Insert to lock in place.
If needed you can also take a hand file or dremel tool and enlarge the hole towards the TOP!
This will allow the Chrome Insert to Snap in to place easier.
You're basically enlarging the holes so that the Shifter Insert Tabs will snap in to the Cradle better.
If you need the Correct Hardware for your Floor Shifter be sure to check out our Floor Shift Hardware Kit
If needed you can also take a hand file or dremel tool and enlarge the hole towards the TOP!
This will allow the Chrome Insert to Snap in to place easier.
You're basically enlarging the holes so that the Shifter Insert Tabs will snap in to the Cradle better.
If you need the Correct Hardware for your Floor Shifter be sure to check out our Floor Shift Hardware Kit
Floor Shift Handle Pull Bar
This is commonly referred to as the "Pull Bar" for an automatic Floor Shift
Fits 1970 - 72
It is crucial that you use the Proper Phillips Screws when installing the Handle and Pull bar or the shifter will not slide up and down properly!
If you need the Correct Hardware for your Floor Shifter be sure to check out our Floor Shift Hardware Kit
Also, when installing the screws that hold the handle & the pull bar in place be sure to place some lube on them and install slowly!! (Otherwise you can crack the plastic)
It is crucial that you use the Proper Phillips Screws when installing the Handle and Pull bar or the shifter will not slide up and down properly!
If you need the Correct Hardware for your Floor Shifter be sure to check out our Floor Shift Hardware Kit
Also, when installing the screws that hold the handle & the pull bar in place be sure to place some lube on them and install slowly!! (Otherwise you can crack the plastic)